湖北地区地震震源参数研究     

申学林  魏贵春  丁文秀  戴苗 《中国地震》2018,34(4):781-787

为了研究湖北地区地震震源参数特征,本文基于湖北数字地震台网记录到的S波观测振幅谱,通过遗传算法获得湖北地区的介质品质因子和台站场地响应,并在此基础上计算了湖北地区地震震源参数。结果显示,湖北地区介质品质因子Q值随频率f变化的关系式为Q(f)=501.8·f~(0.309);对于大部分台站获得了与其岩石基底相符的场地响应,没有出现明显放大效应;地震震级与地震矩对数间呈线性关系,即lg M_0=10.06+1.093M_L;震源半径与应力降间呈双对数线性关系,即lgΔσ=10.52-2.01lgr;地震矩与拐角频率间整体上呈反相关;地震矩与应力降间关系不显著。  相似文献   

应用核磁共振技术分析干盐湖地区地下卤水空间分布特征——以昆特依干盐湖为例   总被引：3，自引：1，他引：2  

杨修猛  刘文玉  韩凤清  韩继龙  HUSSAIN Syed Asim  年秀清  毛庆飞  严维德 《湖泊科学》2018,30(1):220-233

昆特依干盐湖位于柴达木盆地西北部,为特大型综合盐类矿床.大盐滩是昆特依干盐湖内最大的盐滩,地下赋存有一定量的卤水矿床,但该矿床的水文地质条件差,主要卤水矿层含水性弱,开采难度大.核磁共振找水方法作为当今世界上唯一的直接找水地球物理新方法,具有高分辨力、高效率、信息量丰富和解的唯一性等优点,本文运用该方法对昆特依干盐滩地区地下卤水空间分布特征进行研究,通过对核磁共振数据进行处理与反演,结合已有的地质与钻井资料,对测点进行综合地质-地球物理解释,获得以下认识:1)大盐滩0~130 m深度范围内,共存在3个卤水含水层,主要呈扁平状或漏斗状、近似层状展布,W1为晶间潜卤水层,渗透系数较大,颗粒较粗,单位体积含水量为0.4%~2.7%,W2和W3为晶间承压卤水层,渗透系数较小,颗粒较粗,单位体积含水量分别为0.2%~1.1%和0.1%~0.8%;2)大盐滩地区存在两个卤水富集区,分别为研究区西南部沉积盆地中心的Ⅰ号富卤区和盆地东北部的Ⅱ号富卤区;3)根据区域内卤水富集分布以及构造情况,划定大盐滩向斜沉积中心、大盐滩北侧F1~F8及遥F6断裂发育区和冷湖构造带为区域内主要的找矿找水远景区;4)GMR核磁共振系统在干盐滩地区理论探测深度为130 m,该系统不仅可以有效地探测自由水,而且可以依据束缚水的分布解译地下各类含水盐类矿物和含水黏土矿物的存在与分布.  相似文献   

基态位涡径向分布对浅水涡旋系统动力稳定性的影响分析          下载免费PDF全文

刘爽  钟玮  刘宇迪 《地球物理学报》2018,61(6):2207-2219

本文基于正压浅水模型，分析基态位涡（Potential Vorticity：PV）结构对热带气旋（Tropical Cyclone：TC）类涡旋系统稳定性及其波动特征的影响.通过引入基态PV结构参数：宽度δ（眼墙内外边界涡度发生陡变的半径长度之比）和中空度γ（眼心相对涡度与内核区域平均相对涡度之比），设计具有相同基流最大切向风速和最大风速半径的170组不同基态PV环结构的敏感性试验，并讨论了不同基态PV结构下涡旋系统最不稳定波数（the most unstable wavenumber：MUWN）和系统最不稳定模态（the most unstable mode of System：MUMS）的特征频率及其不稳定增长率的大小.结果指出：当PV环较宽，系统表现为低波数最不稳定，相应的MUMS为低频波且增长率小；当PV环较窄，系统表现为高波数不稳定，且PV环越实最不稳定波数越高；当PV环窄且空时，MUMS均为中高频波动，且不稳定增长率随PV环的宽度变窄和中空度变空而明显增大.分析典型PV结构下系统演变特征可知，当PV环较宽，MUMS表现为具有平衡约束的低频波动的线性不稳定特征；当PV环趋向窄且空时，MUMS的平衡性约束趋向弱化，同时不稳定增长表现为明显的指数型增长.进一步讨论系统内部非对称结构的形成和传播机制发现，对于弱不稳定的PV环来说，低波数波最不稳定的特征波动具有典型涡旋Rossby波特征；而对于强不稳定的PV环来说，高波数不稳定的特征波动混合波性质明显.  相似文献   

HOLOCENE ACTIVE CHARACTERISTICS OF THE NORTHERN SEGMENT OF THE MINJIANG FAULT IN THE EASTERN MARGIN OF THE TIBETAN PLATEAU     

LI Feng  LIU Hua-guo  JIA Qi-chao  XU Xi-wei  ZHANG Xiao-liang  GONG Fei 《地震地质》2018,40(1):97-106

As a part of the north-south seismic zone in China, a lot of M6.0-7.2 earthquakes have occurred in the margin faults of the Minshan block in history. This work attempted to characterize the geometry and activity of the north section of the Minjiang fault in this region based on high-resolution satellite images, geologic and geomorphic investigations, micro-geomorphic surveys, and trench excavation. The results show left-lateral-slip and Holocene activity of this structure. Along it, the offset landform has a continuous linearity on Ⅱ terraces near the Chuanpan village. The vertical height of the fault scarp measures 3.1 meters, which is almost the same as the accumulative horizontal displacement of the gully. The accumulative horizontal shortening due to faulting is 3.0 meters. Calculation using the model of displacement-dependent characteristic earthquakes shows both the vertical and horizontal co-seismic displacements and the horizontal shortening amount are about 1.0 meter. While strata dating suggests that the vertical and horizontal slip rates are all about 0.7-0.9mm/a, and the horizontal shortening rate is approximately 1.0-1.1mm/a. The excavated trench, perpendicular to the fault trace, reveals low-angle thrust dipping in 260åt 29°. From the relationship of the fault, colluvial wedge and stratigraphy ages, three palaeoseismic events are identified from youngest to oldest at 0-295a BP, 1 405-1 565a BP, and 2 750-2 875a BP, respectively, with recurrence intervals 1 110-1 565 years and elapsed time about 0-295 years。According to the relationship between magnitude and active parameters, it is considered that the northern segment of the Minjiang fault is capable of generating M7 or greater earthquakes. Now it is in the process of stress accumulation, having a certain seismic risk.  相似文献   

温度对宽频地震计观测资料影响的研究方法   总被引：1，自引：0，他引：1  

王晓蕾  谷国梁  薛兵  朱小毅 《地震》2018,38(3):170-180

本文以具有力平衡反馈结构的甚宽频地震计BBVS-120为分析对象, 通过台站观测实验和实验室温控实验的相关分析, 得到了温度对输出信号影响的频带范围和水平, 定义了温度灵敏度参数, 从定量的角度分析了温度对地震计观测资料的影响。  相似文献   

One-dimensional consolidation of soil under multistage load based on continuous drainage boundary     

Yi--> Tian  Wenbing Wu  Guosheng Jiang  M. Hesham El Naggar  Guoxiong Mei  Meijuan Xu  Rongzhu Liang 《国际地质力学数值与分析法杂志》2020,44(8):1170-1183

In engineering practice, a rapid loading rate can result in ground failure when the strength of soft soils is relatively low, and a multistage loading scheme is always utilized to deal with this situation. Firstly, under a multistage load and the continuous drainage boundary, an analytical solution of excess pore-water pressure and consolidation degree is obtained by virtue of the superposition formula of excess pore-water pressure, and a more general continuous drainage boundary under arbitrary time-dependent load is developed. Then, a comparison with existing analytical solutions is conducted to verify the present solution. A preliminary attempt on applying the continuous drainage boundary into the finite element model is made, and the feasibility of the numerical model for the one-dimensional consolidation under the continuous drainage boundary is verified by comparing the results calculated by FEM with that from present analytical solution. Finally, the consolidation behavior of soil is investigated in detail for different int erface parameters or loading scheme. The results show that, in land reclamation projects, a horizontal drain should be placed close to the boundary with a smaller interface parameter to improve the consolidation efficiency. The degree of consolidation is also related to the applied time-dependent load and interface parameters.  相似文献   

Ekman模型时间变化风应力系数的伴随参数估计     

李国庆  高艳秋  张继才 《海洋与湖沼》2019,50(5):979-993

本文基于时间分布参数设置,利用伴随同化方法,反演了Ekman模型中随时间变化的风应力拖曳系数,并在孪生实验和实际实验中对该方法进行了验证。在孪生实验中,研究了参数反演结果对不同影响因素的响应,包括:风速分布、风应力系数分布、风应力系数初始猜测值、风应力系数独立变量个数、观测数据误差和观测的深度。孪生实验结果验证了伴随同化方法反演Ekman模型中时变风应力系数的有效性,具体包括如下五个方面结论:1)不同风速分布下均能成功反演出不同风应力拖曳系数分布; 2)反演结果对初始猜测值较为敏感,风应力系数初始猜测值越接近给定值,反演结果越好;3)风应力系数独立点个数的选取会显著影响反演结果,合理的选择有利于提高反演效率及减小观测数据误差;4)观测误差能够影响反演结果,观测数据误差在20%以下时能取得合理的反演结果; 5)反演结果对观测数据的表层和次表层流速更为敏感,这是由Ekman流的物理性质决定的。实际实验,利用百慕大锚系试验平台的风速和流速数据,去除周期性潮流和地转流成分后得到Ekman流成分,并作为观测输入到该同化模型,反演出了适用于该区域和该时段的随时间变化的风应力系数。通过比较模拟流速和观测流速,证明利用伴随同化方法能从实测数据中反演出合理的时变风应力系数,对于海洋模型风应力系数的确定是一项有益的尝试。  相似文献   

辽东湾海洋工程可靠性设计的海冰参数选取     

马玉贤  关湃  许宁  许有良  袁帅  刘永青  于福祥 《海洋工程》2019,37(3):136-142

海冰参数的合理取值是海洋工程海冰灾害风险评估的重要内容。利用1950—2018年的冰情等级(5个等级)数据,进行了1950—2018、1950—1990、1991—2018三种情景下的回归分析,确定了不同时期的冰情等级概率分布密度函数。利用鲅鱼圈雷达观测站2002—2017年的海冰现场实测资料,分别对鲅鱼圈附近海域一般冰厚、最大冰厚、最小冰厚进行概率分布拟合。基于上述概率分布结果,给出不同冰情等级的重现期,进而对海冰作业条件给出的设计参考值进行评价。结果表明:1990年以后2级、3级冰情重现期相对1990年之前变小,4级、5级冰情重现期相对1990年之前变大,规范给出重现期范围已不能代表辽东湾冬季海冰情况。本研究成果可为辽东湾海洋工程可靠性设计提供重要数据支撑。  相似文献   

Comparison of two rainfall–runoff models: effects of conceptualization on water budget components     

Vassilios Kaleris  Andreas Langousis 《水文科学杂志》2017,62(5):729-748

Rainfall–runoff models with different conceptual structures for the hydrological processes can be calibrated to effectively reproduce the hydrographs of the total runoff, while resulting in water budget components that are essentially different. This finding poses an open question on the reliability of rainfall–runoff models in reproducing hydrological components other than those used for calibration. In an effort to address this question, we use data from the Glafkos catchment in western Greece to calibrate and compare the ENNS model, a research-oriented lumped model developed for the river Enns in Austria developed for the river Enns in Austria, with the operational MIKE SHE model. Model performance is assessed in the light of the conceptual/structural differences of the modelled hydrological processes, using indices calculated independently for each year, rather than for the whole calibration period, since the former are stricter. We show that even small differences in the representation of hydrological processes may impact considerably on the water budget components that are not measured (i.e. not used for model calibration). From all water budget components, direct runoff exhibits the highest sensitivity to structural differences and related model parameters.